Roland M200-i
|
Processing Channels/Buses CHANNELS: 32 BUSES: MAIN L/R, 8 AUX, 4 MATRIX Inputs/Outputs INPUTS: 24 (64 when using optional REAC devices) OUTPUTS: 14 (Max 54 ports when using REAC Devices) Signal Processing AD/DA Conversion: 24 bit Sample Rate: 48.0 kHz or 44.1 kHz Console Latency 2.0 mS (typ.) *1 * Total Latency of audio signal from M-200i's console inputs to M-200i's outputs. * Sample Rate: 48.0 kHz * Effects: No insert effects Network Latency 2.5 mS (typ.) *1 * Total System Latency of audio signal from S-1608 inputs to outputs via M-200i's REAC ports. * Sample Rate: 48.0 kHz * Effects: No insert effects Connectors Inputs/Outputs/Others INPUT jacks (1 to 16): XLR-3-31 type (balanced, phantom power) INPUT jacks (17 to 22): 1/4 inch Phone type (balanced) INPUT jacks (23 to 24): RCA Phono type ASSIGNABLE OUTPUT jacks (1 to 6): XLR-3-32 type (balanced) ASSIGNABLE OUTPUT jacks (7 to 10): 1/4 inch Phone type (balanced) MAIN OUTPUT jacks (L, R): XLR-3-32 type (balanced) PHONES jack: Stereo 1/4 inch phone type, Miniature phone type AES/EBU OUT jacks: XLR-3-32 type (110 ohm balanced) REAC port: RJ-45 EtherCon type RS-232C connector: 9-pin D-sub type MIDI connectors (OUT/THRU, IN): 5-pin DIN type USB MEMORY port: USB Type A USB WLAN ADAPTOR port: USB Type A USB COMPUTER port: USB Type B LAN port: RJ45 type DOC CABLE port : 10-pin mini DIN type DOC CABLE port : 10-pin mini DIN type DC IN jack Grounding terminal * XLR type: 1 GND, 2 HOT, 3: COLD * Phantom power: DC+48V (unloaded maximum), 14mA (maximum load, All XLR type inputs) Input/Output Characteristics Frequency Response ASSIGNABLE OUTPUT jacks (1 to 10): -2 dB / +0 dB (20k ohms load, +4 dBu, typ.) MAIN OUTPUT jacks (L, R): -2 dB / +0 dB (20k ohms load, +4 dBu, typ.) PHONES jack: -3 dB / +0 dB (40 ohms load, 150 mW, typ.) * Sample Rate: 48.0 kHz or 44.1 kHz * Input Connector: INPUT 1 to 24 (Pad: ON, Input sens: +4 dBu, 20 Hz to 20 kHz Total Harmonic Distortion + Noise ASSIGNABLE OUTPUT jacks (1 to 10): 0.05 % (+4 dBu, typ.) MAIN OUTPUT jacks (L, R): 0.05 % (+4 dBu, typ.) PHONES jack: 0.05 % (40 ohms load, 150 mW, typ.) * Sample Rate: 48.0 kHz or 44.1 kHz * Input Connector: INPUT 1 to 24 (Input sens: +4 dBu, 20 Hz to 20 kHz) Dynamic Range ASSIGNABLE OUTPUT jacks (1 to 10): 102 dB (typ.) MAIN OUTPUT jacks (L, R): 102 dB (typ.) * Sample Rate: 48.0 kHz or 44.1 kHz * Input Connector: INPUT 1 to 24 (Input sens: +4 dBu, 20 Hz to 20 kHz) Crosstalk@ 1 kHz INPUT jacks (1 to 24): -80dB (Input sens: +4 dBu, IHF-A, typ.) ASSIGNABLE OUTPUT jacks (1 to 10): -88 dB (typ.) MAIN OUTPUT jacks (L, R): -88 dB (typ.) * Sample Rate: 48.0 kHz or 44.1 kHz Nominal Input Level (Variable) INPUT jacks (1 to 16): -65 to +4 dBu INPUT jacks (17 to 24): -28 to +4 dBu Input Impedance INPUT jacks (1 to 16): 14 k ohms INPUT jacks (17 to 24): 10 k ohms Non Clip Maximum Input level INPUT jacks (1 to 24): +22dBu (1 kHz, 20 k ohms load, typ.) Nominal Output Level ASSIGNABLE OUTPUT jacks (1 to 10): +4 dBu (Load impedance: 10 k ohms, typ.) MAIN OUTPUT jacks (L, R): +4 dBu (Load impedance: 10 k ohms, typ.) Output Impedance ASSIGNABLE OUTPUT jacks (1 to 10): 600 ohms (typ.) MAIN OUTPUT jacks (L, R): 600 ohms (typ.) PHONES jack: 49 ohms (typ.) Recommended Load Impedance ASSIGNABLE OUTPUT jacks (1 to 10): 10 k ohms or greater MAIN OUTPUT jacks (L, R): 10 k ohms or greater PHONES jack: 40 ohms or greater Minimum Load Impedance PHONES jack: 16 ohms Non Clip Maximum Output level ASSIGNABLE OUTPUT jacks (1 to 10): +22 dBu (1 kHz, 10 k ohms load, typ.) MAIN OUTPUT jacks (1 to 10): +22 dBu (1 kHz, 10 k ohms load, typ.) PHONES jack: 150 mW + 150 mW (1 kHz, 40 ohms load, typ.) Residual Noise Level (IHF-A, typ.) -88 dBu (All faders: Min) -80 dBu (Main Fader: Unity, Channel faders: Unity only one INPUT1 channel, Preamp sens: Min) -61 dBu (Main Fader: Unity, Channel faders: Unity only one INPUT1 channel, Preamp sens: Max) * Input 150 ohms terminate * Output Connector: ASSIGNABLE OUTPUT jacks (1 to 10), MAIN OUTPUT jacks (L, R) * Sample Rate: 48.0 kHz or 44.1 kHz Equivalent Input Noise Level (E.I.N.) -126 dBu (Main Fader: Unity, Channel faders: Unity only one channel, Preamp sens: Max) * Output Connector: ASSIGNABLE OUTPUT jacks (1 to 10), MAIN OUTPUT jacks (L, R) * Sample Rate: 48.0 kHz or 44.1 kHz Others Display Graphic LCD 132 x 64 dots with backlight Current Draw 3.6 A Operation Temperature +5 to +40 degrees Celsius +41 to +104 degrees Fahrenheit Accessories DOCK CABLE, TABLET STAND, AC Adaptor, Power Cord, Owner's Manual Options Rackmount Kit: RA-10U, Wireless USB Adapter: WNA1100-RL USB Flash Memory Size and Weight Width 491 mm Depth 490 mm Height 198 mm Weight 9.8 kg Notes Use USB Flash Memory sold by Roland. Other products are not guaranteed to work.
|
|